Ametek PLA-PLW Programming Manual Manual de usuario Pagina 64
- Pagina / 74
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
60
INPUT POWER
All models have a programmable power function. The command to program the current
is:
POWer <n>
where <n> is the input power in watts.
Maximum Power
The maximum input power that can be programmed can be queried with:
POWer? MAX
Overpower Protection
The electronic load can also be programmed to turn off its input if the power protection
level is reached. This protection feature is implemented the following command:
POWer:PROTection <NRf+>
POWer:PROTection:STATe ON | OFF
Underpower Protection
The electronic load can also be programmed to turn off its input if its input current is
lower than the under-power protection level. This protection feature is implemented the
following command:
POWer:PROTection:UNDer <NRf+>
POWer:PROTection:UNDer:STATe ON | OFF
INPUT RESISTANCE
The input resistance is controlled with the RESistance command. For example, to set
the input resistance to 25 ohms, use:
RESistance 25
Maximum Resistance
The maximum input resistance that can be programmed can be queried with:
RESistance? MAX
INPUT VOLTAGE
The input voltage is controlled with the VOLTage command. For example, to set the
input voltage to 25 volts, use:
VOLTage 25
Maximum Voltage
The maximum input voltage that can be programmed can be queried with:
- PROGRAMMING MANUAL 1
- WARRANTY INFORMATION 3
- Contents 5
- DESCRIPTION 11
- INTRODUCTION 16
- CALIBRATION COMMANDS 16
- CALibrate:POINt 17
- CALibrate:SAVe 17
- CALibrate:STATe 17
- CALibrate:VALue:VOLTage 18
- CALibrate:TRANsient:OFFSet 18
- CALibrate:VALue:CURRent 18
- CURRENT SUBSYSTEM 19
- [SOURce:]CURRent:SLEW:BOTH 21
- [SOURce:]CURRent:TLEVel, ITR 22
- INPUT COMMANDS 24
- STEP COMMANDS 25
- [SOURce:]STEP:CURRent:STATe 26
- [SOURce:]STEP:POWer[:LEVel] 26
- [SOURce:]STEP:POWer:TIMe? 26
- [SOURce:]STEP:POWer:STATe 27
- [SOURce:]STEP:VOLTage[:LEVel] 28
- [SOURce:]STEP:VOLTage:TIMe? 28
- [SOURce:]STEP:VOLTage:STATe 28
- MEASUREMENT COMMANDS 30
- MODE COMMANDS 31
- PORT COMMANDS 32
- INPUT CONTACTOR COMMANDS 32
- POWER SUBSYSTEM 33
- [SOURce:]POWer:SLEW:BOTH 35
- [SOURce:]POWer:SLEW:NEGative 36
- [SOURce:]POWer:TLEVel, PTR 36
- RESISTANCE SUBSYSTEM 38
- [SOURce:]RESistance:SLEW:BOTH 39
- Unit ms 41
- RESistance:TWIDth? 41
- STATUS COMMANDS 42
- STATus:OPERation:NTRansition 43
- STATus:OPERation:PTRansition 43
- STATus:QUEStionable? 47
- STATus:QUEStionable:ENABle 47
- SYSTEM COMMANDS 48
- SYSTem:CROSs:MODe:STATe 49
- SYSTem:CROSs:RANGe:STATe 49
- SYSTem:EOS 49
- SYSTem:ERRor? 49
- SYSTem:EXTernal:CONTrol 51
- SYSTem:GPIB:ADDRess 51
- SYSTem:GPIB:EOS 51
- SYSTem:INPut:BOOT 51
- SYSTem:MODel 51
- SYSTem:NET:ADDRess 52
- SYSTem:NET:DHCP 52
- SYSTem:NET:EOS 52
- SYSTem:NET:GATewa y 52
- SYSTem:NET:STATe 52
- SYSTem:NET:SUBNet 53
- SYSTem:RANGe 53
- SYSTem:SERial? 53
- SYSTem:SHORT:STATus? 53
- SYSTem:VERSion? 53
- TRANSIENT COMMANDS 54
- TRIGGER COMMANDS 55
- 56
- UTILITY COMMANDS 57
- VOLTAGE SUBSYSTEM 58
- [SOURce:]VOLTage:SLEW:BOTH 60
- [SOURce:]VOLTage:TLEVel, VTR 61
- POWER-ON INITIALIZATION 63
- INPUT CURRENT 63
- INPUT POWER 64
- INPUT RESISTANCE 64
- INPUT VOLTAGE 64
- PROGRAMMING TRANSIENTS 65
- CONTINUOUS TRANSIENTS 66
- PULSE TRANSIENTS 67
- TOGGLED TRANSIENTS 67
- PROGRAMMING STEPS 68
- STATE AUTO 69
- STATE ONCE 69
- (other statements) 70
- MAKING MEASUREMENTS 71
- SLEW:BOTH <NRf+> 73
- SLEW:NEG <NRf+> 73
- TLEV <NRf+> 73
- TRAN:TWID <NRf+> 73
- VOLTAGE CALIBRATION 74
- RESISTANCE CALIBRATION 74
Relacionado con productos y manuales para Equipo Ametek PLA-PLW Programming Manual
Equipo Ametek LPDC-16V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek PLA-PLW Manual de usuario
(128 paginas)
(128 paginas)
Equipo Ametek LPDC-65V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPDC-450V Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek FPDC Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek ACPS Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPAL Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek SFA Series Manual de usuario
(64 paginas)
(64 paginas)
Equipo Ametek ReFlex Manual de usuario
(359 paginas)
(359 paginas)
Equipo Ametek SGWC Series Manual de usuario
(21 paginas)
(21 paginas)
Equipo Ametek SGA Series Manual de usuario
(97 paginas)
(97 paginas)
Equipo Ametek SLD Series Manual de usuario
(89 paginas)
(89 paginas)
Equipo Ametek SGI Series Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales