Ametek PLA-PLW Programming Manual Manual de usuario Pagina 43
- Pagina / 74
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
41
STATus:OPERation:NTRansition
STATus:OPERation:PTRansition
These commands set or read the value of the Operation NTR (Negative-Transition) and PTR
(Positive-Transition) registers. These registers serve as polarity filters between the Operation Enable
and Operation Event registers to cause the following actions. This command is not channel specific, it
applies to the entire mainframe.
႑
When a bit in the Operation NTR register is set to 1, then a 1-to-0 transition of the
corresponding bit in the Operation Condition register causes that bit in the
Operation Event register to be set.
႑
When a bit of the Operation PTR register is set to 1, then a 0-to-1 transition of the
corresponding bit in the Operation Condition register causes that bit in the
Operation Event register to be set.
႑
If the same bits in both NTR and PTR registers are set to 1, then any transition of that
bit at the Operation Condition register sets the corresponding bit in the Operation
Event register.
႑
If the same bits in both NTR and PTR registers are set to 0, then no transition of that
bit at the Operation Condition register can set the corresponding bit in the Operation
Event register.
NOTE : Setting a bit in the PTR or NTR filter can of itself generate positive or negative events in the
corresponding Operation Event register.
Command Syntax STATus:OPERation:NTR <NR1>
STATus:OPERation:PTR <NR1>
Parameters 0 to 32767 | MIN | MAX
Default Value 0
Query Syntax STATus:OPERation:NTR?
STATus:OPERation:PTR?
Returned Parameters <NR1> (register value)
Bit configuration of Operation Enable register.
Bit Position 7 6 5 4 3 2 1 0
Bit Name RSF RC OT UP OP UC OC VF
Bit Weight 218 64 32 16 8 4 2 1
Bit Position 15 14 13 12 11 10 9 8
Bit Name LVP OSC PS UV OV UNR RI UVL
Bit Weight 32768 16384 8192 4096 2048 1024 512 256
VF Voltage fault has occurred
OC Over-current has occurred
UC Under-current has occurred
OP Over-power has occurred
UP Under-power has occurred
OT Over-temperature has occurred
RC Reverse-current has occurred
RSF Remote sense fault has occurred
UVL Under-voltage lock out has occurred
RI Remote Inhibition has occurred
UNR Input is unregulated
OV Over-voltage has occurred
UV Under-voltage has occurred
PS Protection shutdown circuit has tripped
OSC Oscillation protection has occurred
LV Low-voltage has occurred
Important Note: Please refer to the eLOAD Operation Manual for Protection or Fault Condition Descriptions
- PROGRAMMING MANUAL 1
- WARRANTY INFORMATION 3
- Contents 5
- DESCRIPTION 11
- INTRODUCTION 16
- CALIBRATION COMMANDS 16
- CALibrate:POINt 17
- CALibrate:SAVe 17
- CALibrate:STATe 17
- CALibrate:VALue:VOLTage 18
- CALibrate:TRANsient:OFFSet 18
- CALibrate:VALue:CURRent 18
- CURRENT SUBSYSTEM 19
- [SOURce:]CURRent:SLEW:BOTH 21
- [SOURce:]CURRent:TLEVel, ITR 22
- INPUT COMMANDS 24
- STEP COMMANDS 25
- [SOURce:]STEP:CURRent:STATe 26
- [SOURce:]STEP:POWer[:LEVel] 26
- [SOURce:]STEP:POWer:TIMe? 26
- [SOURce:]STEP:POWer:STATe 27
- [SOURce:]STEP:VOLTage[:LEVel] 28
- [SOURce:]STEP:VOLTage:TIMe? 28
- [SOURce:]STEP:VOLTage:STATe 28
- MEASUREMENT COMMANDS 30
- MODE COMMANDS 31
- PORT COMMANDS 32
- INPUT CONTACTOR COMMANDS 32
- POWER SUBSYSTEM 33
- [SOURce:]POWer:SLEW:BOTH 35
- [SOURce:]POWer:SLEW:NEGative 36
- [SOURce:]POWer:TLEVel, PTR 36
- RESISTANCE SUBSYSTEM 38
- [SOURce:]RESistance:SLEW:BOTH 39
- Unit ms 41
- RESistance:TWIDth? 41
- STATUS COMMANDS 42
- STATus:OPERation:NTRansition 43
- STATus:OPERation:PTRansition 43
- STATus:QUEStionable? 47
- STATus:QUEStionable:ENABle 47
- SYSTEM COMMANDS 48
- SYSTem:CROSs:MODe:STATe 49
- SYSTem:CROSs:RANGe:STATe 49
- SYSTem:EOS 49
- SYSTem:ERRor? 49
- SYSTem:EXTernal:CONTrol 51
- SYSTem:GPIB:ADDRess 51
- SYSTem:GPIB:EOS 51
- SYSTem:INPut:BOOT 51
- SYSTem:MODel 51
- SYSTem:NET:ADDRess 52
- SYSTem:NET:DHCP 52
- SYSTem:NET:EOS 52
- SYSTem:NET:GATewa y 52
- SYSTem:NET:STATe 52
- SYSTem:NET:SUBNet 53
- SYSTem:RANGe 53
- SYSTem:SERial? 53
- SYSTem:SHORT:STATus? 53
- SYSTem:VERSion? 53
- TRANSIENT COMMANDS 54
- TRIGGER COMMANDS 55
- 56
- UTILITY COMMANDS 57
- VOLTAGE SUBSYSTEM 58
- [SOURce:]VOLTage:SLEW:BOTH 60
- [SOURce:]VOLTage:TLEVel, VTR 61
- POWER-ON INITIALIZATION 63
- INPUT CURRENT 63
- INPUT POWER 64
- INPUT RESISTANCE 64
- INPUT VOLTAGE 64
- PROGRAMMING TRANSIENTS 65
- CONTINUOUS TRANSIENTS 66
- PULSE TRANSIENTS 67
- TOGGLED TRANSIENTS 67
- PROGRAMMING STEPS 68
- STATE AUTO 69
- STATE ONCE 69
- (other statements) 70
- MAKING MEASUREMENTS 71
- SLEW:BOTH <NRf+> 73
- SLEW:NEG <NRf+> 73
- TLEV <NRf+> 73
- TRAN:TWID <NRf+> 73
- VOLTAGE CALIBRATION 74
- RESISTANCE CALIBRATION 74
Relacionado con productos y manuales para Equipo Ametek PLA-PLW Programming Manual
Equipo Ametek LPDC-16V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek PLA-PLW Manual de usuario
(128 paginas)
(128 paginas)
Equipo Ametek LPDC-65V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPDC-450V Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek FPDC Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek ACPS Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPAL Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek SFA Series Manual de usuario
(64 paginas)
(64 paginas)
Equipo Ametek ReFlex Manual de usuario
(359 paginas)
(359 paginas)
Equipo Ametek SGWC Series Manual de usuario
(21 paginas)
(21 paginas)
Equipo Ametek SGA Series Manual de usuario
(97 paginas)
(97 paginas)
Equipo Ametek SLD Series Manual de usuario
(89 paginas)
(89 paginas)
Equipo Ametek SGI Series Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.069 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales