Ametek PLA-PLW Programming Manual Manual de usuario Pagina 36
- Pagina / 74
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
34
programmed value. MINimum sets the slew to the fastest possible time. MAXimum sets the slew to
the slowest time. Slew times less than the minimum value are set to MINimum. Slew time greater than
the maximum value are set to MAXimum.
Command Syntax POW:SLEW:BOTH <NRf+>
Parameters Slew time, refer to model specificat
ions
| MIN | MAX
Unit ms
[SOURce:]POWer:SLEW:NEGative
This command sets the slew time of the power for negative going transitions. MINimum sets the slew
to the fastest possible time. MAXimum sets the slew to the slowest time.
Command Syntax POWer:SLEW:NEGative <NRf+>
Parameters Slew time, refer to model specifications | MIN | MAX
Unit ms
Query Syntax POWer:SLEW:NEGative?
POWer:SLEW:NEGative? MIN POWer:SLEW:NEGative? MAX
Returned Parameters <NRf+> slew time in ms
[SOURce:]POWer:SLEW[:POSitive]
This command sets the slew time of the power for positive going transitions. MINimum sets the slew
to the fastest possible time. MAXimum sets the slew to the slowest time.
Command Syntax POWer:SLEW <NRf+>
POWer:SLEW:POSitive <NRf+>
Parameters slew time, refer to model specifications | MIN | MAX
Unit ms
Query Syntax POWer:SLEW?
POWer:SLEW? MIN POWer:SLEW? MAX
POWer:SLEW:POSitive?
POWer:SLEW:POSitive? MIN
POWer:SLEW:POSitive? MAX
Returned Parameters <NRf+> slew time in ms
[SOURce:]POWer:TLEVel, PTR
Channel-Specific Power Command/Query. This command specifies the value of the programmed
power level for the TRANsient input when the electronic load is in the CP Mode. When the Transient
Subsystem is on, the electronic load input power will switch (under control of the Transient Subsystem)
between the main level and TLEVel at a rate determined by the present value of SLEW.
In order for the input power level to switch, TLEVel must be set to a value greater than the main level.
If TLEVel is set to a value below the main level, no error is generated bu
t s
witching will not occur until
the main level is subsequently below the value of TLEVel.
Command Syntax POWer:TLEVel <NRf+>
PTR <NRf+>
Parameters Power transient level value, refer to model specifications for range.
Query Syntax POWer:TLEVel?
POWer:TLEVel? MIN POWer:TLEVel? MAX
PTR?
PTR? MIN PTR? MAX
Returned Parameters <NRf+> “POW:TLEV?” returns the transient power level.
- PROGRAMMING MANUAL 1
- WARRANTY INFORMATION 3
- Contents 5
- DESCRIPTION 11
- INTRODUCTION 16
- CALIBRATION COMMANDS 16
- CALibrate:POINt 17
- CALibrate:SAVe 17
- CALibrate:STATe 17
- CALibrate:VALue:VOLTage 18
- CALibrate:TRANsient:OFFSet 18
- CALibrate:VALue:CURRent 18
- CURRENT SUBSYSTEM 19
- [SOURce:]CURRent:SLEW:BOTH 21
- [SOURce:]CURRent:TLEVel, ITR 22
- INPUT COMMANDS 24
- STEP COMMANDS 25
- [SOURce:]STEP:CURRent:STATe 26
- [SOURce:]STEP:POWer[:LEVel] 26
- [SOURce:]STEP:POWer:TIMe? 26
- [SOURce:]STEP:POWer:STATe 27
- [SOURce:]STEP:VOLTage[:LEVel] 28
- [SOURce:]STEP:VOLTage:TIMe? 28
- [SOURce:]STEP:VOLTage:STATe 28
- MEASUREMENT COMMANDS 30
- MODE COMMANDS 31
- PORT COMMANDS 32
- INPUT CONTACTOR COMMANDS 32
- POWER SUBSYSTEM 33
- [SOURce:]POWer:SLEW:BOTH 35
- [SOURce:]POWer:SLEW:NEGative 36
- [SOURce:]POWer:TLEVel, PTR 36
- RESISTANCE SUBSYSTEM 38
- [SOURce:]RESistance:SLEW:BOTH 39
- Unit ms 41
- RESistance:TWIDth? 41
- STATUS COMMANDS 42
- STATus:OPERation:NTRansition 43
- STATus:OPERation:PTRansition 43
- STATus:QUEStionable? 47
- STATus:QUEStionable:ENABle 47
- SYSTEM COMMANDS 48
- SYSTem:CROSs:MODe:STATe 49
- SYSTem:CROSs:RANGe:STATe 49
- SYSTem:EOS 49
- SYSTem:ERRor? 49
- SYSTem:EXTernal:CONTrol 51
- SYSTem:GPIB:ADDRess 51
- SYSTem:GPIB:EOS 51
- SYSTem:INPut:BOOT 51
- SYSTem:MODel 51
- SYSTem:NET:ADDRess 52
- SYSTem:NET:DHCP 52
- SYSTem:NET:EOS 52
- SYSTem:NET:GATewa y 52
- SYSTem:NET:STATe 52
- SYSTem:NET:SUBNet 53
- SYSTem:RANGe 53
- SYSTem:SERial? 53
- SYSTem:SHORT:STATus? 53
- SYSTem:VERSion? 53
- TRANSIENT COMMANDS 54
- TRIGGER COMMANDS 55
- 56
- UTILITY COMMANDS 57
- VOLTAGE SUBSYSTEM 58
- [SOURce:]VOLTage:SLEW:BOTH 60
- [SOURce:]VOLTage:TLEVel, VTR 61
- POWER-ON INITIALIZATION 63
- INPUT CURRENT 63
- INPUT POWER 64
- INPUT RESISTANCE 64
- INPUT VOLTAGE 64
- PROGRAMMING TRANSIENTS 65
- CONTINUOUS TRANSIENTS 66
- PULSE TRANSIENTS 67
- TOGGLED TRANSIENTS 67
- PROGRAMMING STEPS 68
- STATE AUTO 69
- STATE ONCE 69
- (other statements) 70
- MAKING MEASUREMENTS 71
- SLEW:BOTH <NRf+> 73
- SLEW:NEG <NRf+> 73
- TLEV <NRf+> 73
- TRAN:TWID <NRf+> 73
- VOLTAGE CALIBRATION 74
- RESISTANCE CALIBRATION 74
Relacionado con productos y manuales para Equipo Ametek PLA-PLW Programming Manual
Equipo Ametek LPDC-16V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek PLA-PLW Manual de usuario
(128 paginas)
(128 paginas)
Equipo Ametek LPDC-65V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPDC-450V Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek FPDC Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek ACPS Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPAL Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek SFA Series Manual de usuario
(64 paginas)
(64 paginas)
Equipo Ametek ReFlex Manual de usuario
(359 paginas)
(359 paginas)
Equipo Ametek SGWC Series Manual de usuario
(21 paginas)
(21 paginas)
Equipo Ametek SGA Series Manual de usuario
(97 paginas)
(97 paginas)
Equipo Ametek SLD Series Manual de usuario
(89 paginas)
(89 paginas)
Equipo Ametek SGI Series Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales