Ametek PLA-PLW Programming Manual Manual de usuario Pagina 20
- Pagina / 74
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
18
Returned Parameters <NRf+>: “CURR?” and “CURR:TRIG?” return the presently programmed
current levels. After a trigger signal or “ABORt”, “CURR:TRIG?” returns
the same value as “CURR?”.
“CURR? MAX”, “CURR? MIN”, “CURR:TRIG? MA X” and
“CURR:TRIG?” MIN return the maximum and minimum programmable
LEVel values.
[SOURce:]CURRent:[TRANsient:]DUTY
This command sets the duty cycle of each of the transients when the generator is in CONTinuous
mode.
Command Syntax CURRent:[TRANient:]DUTY <NR1>
Parameters <NR1>: Duty cycle value. 1 – 100.
Unit Percentage (%)
Query Syntax CURRent:DUTY?
CURRent:DUTY? MIN CURRent:DUTY? MAX
CURRent:TRANsient:DUTY?
CURRent:TRANsient:DUTY? MIN
CURRent:TRANsient:DUTY? MAX
Returned Parameters <NR1>, duty cycle value in percentage
[SOURce:]CURRent:[TRANsient:]FREQuency
This command sets the frequency of the transients when the generator is in CONTinuous mode.
Command Syntax CURRent:[TRANsient:]FREQuency <NRf+>
Parameters <NRf+>: Frequency value, refer to model specifications for range.
Unit Hertz
Query Syntax CURRent:FREQuency?
CURRent:FREQuency? MIN CURRent:FREQuency? MAX
CURRent:TRANsient:FREQuency?
CURRent:TRANsient:FREQuency? MIN
CURRent:TRANsient:FREQuency? MAX
Returned Parameters <NRf+>
[SOURce:]CURRent:PROTection[:LEVel]
[SOURce:]CURRent:PROTection:DELay
[SOURce:]CURRent:PROTection:OVER[:LEVel]
[SOURce:]CURRent:PROTection:OVER:DELay
[SOURce:]CURRent:PROTection:STATe
[SOURce:]CURRent:PROTection:UNDer[:LEVel]
[SOURce:]CURRent:PROTection:UNDer:DELay
[SOURce:]CURRent:PROTection:UNDer:STATe
Channel-Specific Current Limiting Command/Query. This command sets the over-current
protection limit or the under-current protection limit to the input current that the electronic load will sink.
When the input current reaches the over-current protection limit or falls below the under-current
protection limit for the specified delay period, the input of the electronic load is shut off and draws no
current.
The INPut:PROTection:CLEar command (or front panel key) re-enables the input current. The trigger
activated current functions (CURR[:LEV]:TRIG and CURR:TLEV) automatically keep track of
- PROGRAMMING MANUAL 1
- WARRANTY INFORMATION 3
- Contents 5
- DESCRIPTION 11
- INTRODUCTION 16
- CALIBRATION COMMANDS 16
- CALibrate:POINt 17
- CALibrate:SAVe 17
- CALibrate:STATe 17
- CALibrate:VALue:VOLTage 18
- CALibrate:TRANsient:OFFSet 18
- CALibrate:VALue:CURRent 18
- CURRENT SUBSYSTEM 19
- [SOURce:]CURRent:SLEW:BOTH 21
- [SOURce:]CURRent:TLEVel, ITR 22
- INPUT COMMANDS 24
- STEP COMMANDS 25
- [SOURce:]STEP:CURRent:STATe 26
- [SOURce:]STEP:POWer[:LEVel] 26
- [SOURce:]STEP:POWer:TIMe? 26
- [SOURce:]STEP:POWer:STATe 27
- [SOURce:]STEP:VOLTage[:LEVel] 28
- [SOURce:]STEP:VOLTage:TIMe? 28
- [SOURce:]STEP:VOLTage:STATe 28
- MEASUREMENT COMMANDS 30
- MODE COMMANDS 31
- PORT COMMANDS 32
- INPUT CONTACTOR COMMANDS 32
- POWER SUBSYSTEM 33
- [SOURce:]POWer:SLEW:BOTH 35
- [SOURce:]POWer:SLEW:NEGative 36
- [SOURce:]POWer:TLEVel, PTR 36
- RESISTANCE SUBSYSTEM 38
- [SOURce:]RESistance:SLEW:BOTH 39
- Unit ms 41
- RESistance:TWIDth? 41
- STATUS COMMANDS 42
- STATus:OPERation:NTRansition 43
- STATus:OPERation:PTRansition 43
- STATus:QUEStionable? 47
- STATus:QUEStionable:ENABle 47
- SYSTEM COMMANDS 48
- SYSTem:CROSs:MODe:STATe 49
- SYSTem:CROSs:RANGe:STATe 49
- SYSTem:EOS 49
- SYSTem:ERRor? 49
- SYSTem:EXTernal:CONTrol 51
- SYSTem:GPIB:ADDRess 51
- SYSTem:GPIB:EOS 51
- SYSTem:INPut:BOOT 51
- SYSTem:MODel 51
- SYSTem:NET:ADDRess 52
- SYSTem:NET:DHCP 52
- SYSTem:NET:EOS 52
- SYSTem:NET:GATewa y 52
- SYSTem:NET:STATe 52
- SYSTem:NET:SUBNet 53
- SYSTem:RANGe 53
- SYSTem:SERial? 53
- SYSTem:SHORT:STATus? 53
- SYSTem:VERSion? 53
- TRANSIENT COMMANDS 54
- TRIGGER COMMANDS 55
- 56
- UTILITY COMMANDS 57
- VOLTAGE SUBSYSTEM 58
- [SOURce:]VOLTage:SLEW:BOTH 60
- [SOURce:]VOLTage:TLEVel, VTR 61
- POWER-ON INITIALIZATION 63
- INPUT CURRENT 63
- INPUT POWER 64
- INPUT RESISTANCE 64
- INPUT VOLTAGE 64
- PROGRAMMING TRANSIENTS 65
- CONTINUOUS TRANSIENTS 66
- PULSE TRANSIENTS 67
- TOGGLED TRANSIENTS 67
- PROGRAMMING STEPS 68
- STATE AUTO 69
- STATE ONCE 69
- (other statements) 70
- MAKING MEASUREMENTS 71
- SLEW:BOTH <NRf+> 73
- SLEW:NEG <NRf+> 73
- TLEV <NRf+> 73
- TRAN:TWID <NRf+> 73
- VOLTAGE CALIBRATION 74
- RESISTANCE CALIBRATION 74
Relacionado con productos y manuales para Equipo Ametek PLA-PLW Programming Manual
Equipo Ametek LPDC-16V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek PLA-PLW Manual de usuario
(128 paginas)
(128 paginas)
Equipo Ametek LPDC-65V Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPDC-450V Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek FPDC Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek ACPS Manual de usuario
(4 paginas)
(4 paginas)
Equipo Ametek HPAL Manual de usuario
(3 paginas)
(3 paginas)
Equipo Ametek SFA Series Manual de usuario
(64 paginas)
(64 paginas)
Equipo Ametek ReFlex Manual de usuario
(359 paginas)
(359 paginas)
Equipo Ametek SGWC Series Manual de usuario
(21 paginas)
(21 paginas)
Equipo Ametek SGA Series Manual de usuario
(97 paginas)
(97 paginas)
Equipo Ametek SLD Series Manual de usuario
(89 paginas)
(89 paginas)
Equipo Ametek SGI Series Manual de usuario
(128 paginas)
(128 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.106 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales