Ametek ReFlex Programming Manual Manual de usuario Pagina 67
- Pagina / 134
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
DC Module Remote Programming ReFlex Power™ Programming Manual
M380056-03 Rev L 63
3.9.2 SOURCE
SCPI
C
OMMAND
R
EFERENCE
Command
Description
SOURce<n>
Source subsystem. Module ‘n’.
:CURRent <NRf>
Sets the output current in amps.
:CURRent?
Query the set output current in amps.
:LIMit <NRf>
Sets an upper soft limit on the programmed output current for
the supply.
:LIMit?
Query an upper soft limit on the programmed output current
for the supply.
:PROTection <NRf>
Sets the overcurrent protection trip point in amps
:PROTection?
Query the overcurrent protection trip point in amps
:TRACKing <bool>
Set the over current protection to tracking. 1 means turn on
the tracking supervisory and 0 means turn off the tracking
supervisory
:TRACKing?
Query the tracking supervisory status.
:MODE?
Query, 1 is constant current mode, 0 is voltage mode. See
OUTP[n]:PROT:FOLD command.
:RAMP
See Table 3-9. For Software Ramps
:TRIGger
See Table 3-8. For Software Setpoints
:VOLTage <NRf>
Sets the output voltage of the supply in volts. *See note at end
of this table.
:VOLTage?
Query the set point of the output voltage of the supply in volts.
:LIMit <NRf>
Sets the upper soft limit on the programmed output voltage.
:LIMit?
Query an upper soft limit on the programmed output voltage.
:PROTection <NRf>
Sets the overvoltage protection trip point in volts.
:PROTection?
Query the set point of the overvoltage protection trip point in
volts.
:TRACKing <bool>
Set the over voltage protection mode to tracking. 1 equals on,
and 0 turns off the tracking supervisory.
:TRACKing?
Query the tracking supervisory status.
:ENABle <bool>
Disable OVP when OFF, Save current setting, and set OVP to
factory maximum value. When ON, restore the saved OVP
setting.
:ENABle?
Query if OVP is Enabled or Disabled.
:RAMP
See Table 3-9. For Software Ramps
:TRIGger
See Table 3-8. For Software Setpoints
:UNDERVOLTage
:PROTection <NRf>
Sets the undervoltage protection trip point in volts.
:PROTection?
Query the set point of the undervoltage protection trip point in
volts.
:TRACKing <bool>
Set under voltage protection tracking. 1 = On, 0= Off.
:TRACKing?
Query the tracking supervisory status.
:TRIPped?
Returns 1 if the supply has an undervoltage fault
*Note: Set and Query the state of the polarity relay using the OUTPut<n>:POLarity
command.
- ReFlex Power™ 1
- (“AMETEK”): 5
- SAFETY SYMBOLS 7
- CONTENTS 11
- LIST OF TABLES 17
- LIST OF FIGURES 18
- REMOTE PROGRAMMING OVERVIEW 19
- 1.4.1 F 21
- 18 M380056-03 Rev M 22
- CONTROLLER MODULE REMOTE 23
- CONFIGURATION 24
- THERNET 25
- ROCEDURE 25
- 2.4.3 L 26
- M380056-03 Rev L 23 27
- 2.5.1 H 28
- 2.5.2 LOGIN 29
- 2.5.3 IP 30
- 28 M380056-03 Rev M 32
- 2.5.4 S 33
- 2.5.5 M 36
- Figure 2-13. Net Test Window 37
- 2.6.1 M 39
- SCPI COMMAND OPERATION 40
- 2.8.4 Q 43
- EIB SCPI COMMANDS 45
- SYSTEM:NETWORK SCPI COMMANDS 46
- 2.11.2 SYSTEM:NETWORK 47
- RFP SERVICE REQUEST 48
- XECUTION TIME 50
- PERATION 50
- RELATED 51
- 48 M380056-03 Rev M 52
- ETTING THE 53
- BIT IN THE 53
- AN EXAMPLE 53
- TRIGGER SCPI COMMANDS 54
- MEMORY SCPI COMMANDS 55
- 52 M380056-03 Rev M 56
- DC MODULE REMOTE PROGRAMMING 57
- :LOCK 62
- 3.9.2 SOURCE 67
- XTERNAL 72
- RIGGERING 72
- SCPI Command Description 74
- ‘fa’, ‘b’ to ‘fb’… 74
- 72 M380056-03 Rev M 76
- Figure 3-8. List Mode Logic 78
- 78 M380056-03 Rev M 82
- LIST SCPI COMMANDS 86
- 84 M380056-03 Rev M 88
- DC SYSTEM SCPI COMMANDS 89
- 88 M380056-03 Rev M 92
- AC MODULE REMOTE PROGRAMMING 93
- 4.4.2 E 96
- 4.6.2 CALIBRATION 100
- MEASURE SCPI COMMANDS 103
- OUTPUT SCPI COMMANDS 104
- SOURCE SCPI COMMANDS 105
- EFERENCE 106
- cross waveform 107
- STATUS SCPI COMMANDS 110
- M380056-03 Rev L 107 111
- SYSTEM SCPI COMMANDS 112
- PARALLEL GROUPS 112
- 4.12.2 E 113
- 110 M380056-03 Rev L 114
- LOAD MODULE REMOTE 115
- PROGRAMMING 115
- POWER-ON CONDITIONS 116
- ERROR CODES 117
- COMMON SCPI COMMANDS 118
- CALIBRATION SCPI COMMANDS 119
- 5.6.2 CALIBRATION 120
- INPUT SCPI COMMANDS 122
- FIXED POWER DC REMOTE 127
- 6.5.2 CALIBRATION 131
- STATUS COMMANDS 133
- SYSTEM COMMANDS 133
- 130 M380056-03 Rev L 134
Relacionado con productos y manuales para Equipo Ametek ReFlex Programming Manual
Equipo Ametek SFA Series Manual de usuario
(64 paginas)
(64 paginas)
Equipo Ametek ReFlex Manual de usuario
(359 paginas)
(359 paginas)
Equipo Ametek SGWC Series Manual de usuario
(21 paginas)
(21 paginas)
Equipo Ametek SGA Series Manual de usuario
(97 paginas)
(97 paginas)
Equipo Ametek SLD Series Manual de usuario
(89 paginas)
(89 paginas)
Equipo Ametek SGI Series Manual de usuario
(128 paginas)
(128 paginas)
Equipo Ametek SLH Series RevC Manual de usuario
(93 paginas)
(93 paginas)
Equipo Ametek SLH Series RevB Manual de usuario
(81 paginas)
(81 paginas)
Equipo Ametek SLM Series RevC Manual de usuario
(85 paginas)
(85 paginas)
Equipo Ametek SLM Series Rev B Manual de usuario
(87 paginas)
(87 paginas)
Equipo Ametek SL Series Software Manual de usuario
(34 paginas)
(34 paginas)
Equipo Ametek SLM-1 Manual de usuario
(77 paginas)
(77 paginas)
Equipo Ametek SLM-4 Manual de usuario
(77 paginas)
(77 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales