Ametek BPS Series Programming Manual Manual de usuario Pagina 203
- Pagina / 226
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
BPS / MX / RS Series SCPI Programming Manual AMETEK Programmable Power
Manual P/N 7003-961 Rev. AA 203
REGenerate:DELay:FREQuency[:SHUTdown]
This command will set the delay in seconds before applying the programmed frequency
deviation in an attempt to shut down the inverter under test. Available setting range is 0.25
to 10.0 seconds. If the frequency deviation is set to 0.0 Hz, no frequency shift will be
asserted. If set to a value other than zero hertz, the frequency shift will be applied when the
fed back current exceeds the programmed current limit for more than the delay set by the
REG:DEL:FREQ command.
Command Syntax REGenerate:DELay:FREQuency[:SHUTdown] <Nrf>
Parameters 0.25 to 10, time in seconds.
Examples REG:DEL:FREQ 3
Query Syntax REGenerate:DELay:FREQuency[:SHUTdown]?
Returned Parameters <NR2>
REGenerate:DELay:OUTPut[:SHUTdown]
This command will set the delay in seconds before shutting down the power source output in
an attempt to shut down the inverter under test. Available setting range is 0.25 to 10.0
seconds. If the frequency deviation is set to 0.0 Hz, no frequency shift will be asserted. If set
to a value other than zero hertz, the frequency shift will be applied first when the fed back
current exceeds the programmed current limit for more than the delay set by the
REG:DEL:FREQ command. If the current fed back by the EUT still exceeds the programmed
current limit, the output voltage will be set to the lower voltage limit and the output relay will
open after this delay expires.
Command Syntax REGenerate:DELay:OUTPut[:SHUTdown] <Nrf>
Parameters 0.25 to 10, time in seconds.
Examples REG:DEL:OUTP 3
Query Syntax REGenerate:DELay:OUTPut[:SHUTdown]?
Returned Parameters <NR2>
REGenerate:DEViate:FREQuency
This command will set or query the frequency shift used to shut down the inverter under test.
Available setting range is 0.0 to 5.0 Hz. If the frequency deviation is set to 0.0 Hz, no
frequency shift will be asserted. If set to a value other than zero hertz, the frequency shift will
be applied when the fed back current exceeds the programmed current limit for more than
the delay set by the REG:DEL:FREQ command.
Command Syntax REGenerate:DEViate:FREQuency <Nrf>
Parameters 0 to 5
Examples REG:DEV:FREQ 3
Query Syntax REGenerate:DEViate:FREQuency?
Returned Parameters <NR2>
- BPS / Mx / RS Series 1
- SCPI Programming Manual 1
- WARNING 4
- SAFETY SYMBOLS 5
- Warranty Period: 1 Year 6
- WARRANTY TERMS 6
- PRODUCT RETURN PROCEDURE 6
- Table of Contents 7
- Table of Figures 9
- Table of Tables 9
- Introduction 10
- Model BPS Series 11
- External References 11
- Introduction to Programming 12
- Introduction to SCPI 14
- Types of SCPI Messages 15
- The SCPI Command Tree 15
- Using Queries 17
- Structure of a SCPI Message 17
- The Message Unit 17
- Combining Message Units 18
- Headers 19
- Query Indicator 19
- Message Unit Separator 19
- Root Specifier 20
- Message Terminator 20
- SCPI Data Formats 21
- Numerical Data Formats 21
- Character Data 21
- GPIB Controllers 22
- Agilent 82350 Driver 22
- RS232C Interface 24
- Serial Cable Diagram 25
- USB Driver Installation 26
- USB Interface 26
- USB Interface Use 34
- LAN Interface Option 35
- MAC Address 35
- Setting the TCP/IP Address 35
- Socket Port Number 37
- IP Ping 37
- SCPI Command Reference 38
- Calibration Subsystem 39
- [:SOURce] 40
- :HRANge 40
- :IMPedance 40
- Current Measurement 42
- Voltage Measurement 44
- Output Phase 46
- Output - AC Voltage 47
- Output - DC Voltage 49
- Display Subsystem 51
- Instrument Subsystem 53
- Current Array Data 56
- Voltage Array Data 60
- Phase Measurement Subsystem 67
- Power Measurement Subsystem 68
- Output Subsystem 73
- Output Relay 73
- Output Protection 74
- Output Remote Inhibit Modes 74
- External Trigger Output 76
- Source Subsystem - Current 79
- Source Subsystem - Frequency 81
- Source Subsystem - Limit 86
- Source Subsystem - List 90
- List - Count 91
- List - Dwell 91
- List - Frequency 92
- List - Repeat 94
- List - Step 94
- List:TTL Trigger Out 95
- List:Voltage 96
- Source Subsystem - Mode 98
- Source Subsystem - Phase 99
- Source Subsystem - PONSetup 100
- Source Subsystem - Pulse 104
- Source Subsystem - Voltage 107
- Status Subsystem Commands 113
- System Commands 117
- Trigger Subsystem 126
- Common Commands 131
- 5.1 *CLS 132
- 5.2 *ESE 133
- 5.3 *ESR? 133
- 5.4 *IDN? 134
- 5.5 *OPC 134
- 5.6 *OPT? 135
- 5.7 *PSC 136
- 5.8 *RCL 136
- 5.9 *RST 137
- 5.10 *SAV 138
- 5.11 *SRE 138
- 5.12 *STB? 139
- 5.13 *TRG 140
- 5.14 *WAI 140
- Programming Examples 141
- Programming the Output 142
- Power-on Initialization 142
- Enabling the Output 142
- AC Voltage and Frequency 142
- Programming the Output Phase 144
- Current Limit 144
- Waveform Shapes 145
- Individual Phases 146
- Coupled Commands 147
- FIXED mode 149
- STEP mode 149
- PULSE mode 149
- LIST mode 149
- Step and Pulse Transients 150
- List Transients 151
- Triggering Output Changes 153
- Trigger System Model 153
- Generating Triggers 155
- Acquiring Measurement Data 156
- Power Measurements 157
- Frequency Measurements 157
- Harmonic Measurements 158
- Triggering Measurements 159
- TRIGGER RECEIVED 160
- INIT[:IMM]:ACQ 160
- 4096 DATA POINTS 163
- Trigger System Summary 164
- Status Registers 165
- Questionable Status Group 168
- Standard Event Status Group 169
- Status Byte Register 169
- Examples 170
- SCPI Command Completion 171
- Option Commands 172
- IEC 1000-4-11 (-411) 173
- IEC 1000-4-13 (-413) 177
- IEC 1000-4-13 Subsystem 177
- Interharmonics Subsystem 188
- RTCA/DO-160D (-160) 190
- VOLTAGE SURGE, for detail 192
- VOLTAGE UNDER 192
- MIL-STD 704E (-704) 197
- AC System 197
- DC System 198
- Programming Considerations 198
- OMNI Reference Impedance 200
- Watt Hour Meter (-WHM) 201
- Current Sink Option (-SNK) 202
- SCPI Version 212
- Appendix C: Error Messages 213
- Table 8-4 : Error Messages 218
Relacionado con productos y manuales para Equipo Ametek BPS Series Programming Manual
Equipo Ametek DLM 600W Series Manual de usuario
(82 paginas)
(82 paginas)
Equipo Ametek BPS Series Manual de usuario
(153 paginas)
(153 paginas)
Equipo Ametek DLM600 Series Manual de usuario
(16 paginas)
(16 paginas)
Equipo Ametek DCS-E 1KW Series Manual de usuario
(65 paginas)
(65 paginas)
Equipo Ametek DLM Series Manual de usuario
(74 paginas)
(74 paginas)
Equipo Ametek M133 Manual de usuario
(8 paginas)
(8 paginas)
Equipo Ametek M130 Manual de usuario
(99 paginas)
(99 paginas)
Equipo Ametek DCS-E 3kW Series Manual de usuario
(94 paginas)
(94 paginas)
Equipo Ametek CTS 3.0 Manual de usuario
(166 paginas)
(166 paginas)
Equipo Ametek CSW Series Manual de usuario
(174 paginas)
(174 paginas)
Equipo Ametek 2003RP Manual de usuario
(126 paginas)
(126 paginas)
Equipo Ametek 2001RP Manual de usuario
(131 paginas)
(131 paginas)
Equipo Ametek RS Series Manual de usuario
(228 paginas)
(228 paginas)
Equipo Ametek Lx AC source Manual de usuario
(2 paginas)
(2 paginas)
Equipo Ametek MX15 Series Manual de usuario
(184 paginas)
(184 paginas)
Equipo Ametek Lx Series II Manual de usuario
(226 paginas)
(226 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales