Ametek DCS-E 1kW Series Programming Manual Manual de usuario

M362250-01 Rev C www.programmablepower.com DCS-E 1kW Series, DLM-E 3kW & 4kW Power Supplies M51A Option: Isolated Analog Programming Manual

Contents DLM-E Series and DCS-E Series LIST OF TABLES Table 2–1. SW1 SETUP Switch...

SECTION 1 M51A OPTION OVERVIEW 1.1 Introduction This manual is to be used in conjunction with the DCS-E 1kW Series & DCS-E 1.2kW Series DC Power

M51A Option Overview DLM-E Series and DCS-E Series 1-2 M51A Option 1.3 Specifications 1.3.1 Electrical Specifications Remote Voltage Programming A

SECTION 2 ISOLATED ANALOG PROGRAMMER OPERATION 2.1 SW1 Switch The SW1 SETUP switch is accessible from the rear panel of the unit. It provides user

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.1.1 SW1 Switch Setup The following sections describe the functions of the vari

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 2.2 ISOLATED ANALOG PROGRAMMER Connector (J4) The ISOLATED ANALOG PROGRAMMER co

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2-4 M51A Option 2.2.1 ISOLATED ANALOG PROGRAMMER Functions The following secti

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation M51A Option 2-5 Analog Programming Signals OVP PROGRAMMING INPUT: Pin-3, an i

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2-6 M51A Option Auxiliary Sources AUXILIARY DC OUTPUT: Pin-15, 16VDC source for

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 2.3 Remote Programming Configuration 2.3.1 Voltage Source Programming of Outpu

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.3.2 Voltage Source Programming of Output Current SW1 Switch Settings SW1-2 ON

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 2.3.3 Voltage Source Programming of OVP SW1 Switch Settings SW1-3 ON (1) = 0–5

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.3.4 Resistance Programming of Output Voltage SW1 Switch Settings SW1-1 ON (1)

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 2.3.5 Resistance Programming of Output Current SW1 Switch Settings SW1-2 ON (1

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.3.6 Resistance Programming of OVP SW1 Switch Settings SW1-3 ON (1) = 0–5K 23

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 2.3.7 4-20mA Current Source Programming of Output Voltage SW1 Switch Settings

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.3.8 4-20mA Current Source Programming of Output Current SW1 Switch Settings S

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 2.3.9 Programming the Shutdown Function 21312515+5VGND14 Figure 2–3. Using Shu

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.3.11 Shutdown Application – Contact Closure An external relay, whether normally

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation 13 125 1514 Figure 2–5. Using Shutdown with Contact Closure of a Normally OPEN

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2.3.12 Local/Remote Application An external relay or switch may be used to select

DLM-E Series and DCS-E Series Isolated Analog Programmer Operation M51A Option 2-19 2.4 Remote Monitoring Analog signals are available for monitor

Isolated Analog Programmer Operation DLM-E Series and DCS-E Series 2-20 M51A Option This page intentionally left blank.

About AMETEK AMETEK Programmable Power, Inc., a Division of AMETEK, Inc., is a global leader in the design and manufacture of precision, programmable

This page intentionally left blank. ii

Important Safety Instructions Before applying power to the system, verify that your product is configured properly for your particular application.

This page intentionally left blank. iv

CONTENTS SECTION 1 M51A OPTION OVERVIEW ............1-1 1.1 Introduction ...........